MCM > Piezas/Kits > Engine Components: Block Hardware
Engine Components: Block Hardware
1/2 NPT Blanking Plug
- Descripción:
- Socket head pipe plug for use in blanking unused positions in intake manifold, block etc. 1 plug 1/2-inch NPT. Usually used to blank water temperature points in intake manifold or cylinder head. For help in identification, this plug measures approximately 21mm OD.
- Fabricante:
- Edelbrock
- PVP:
- —
- IVA incluído:
- —
1/4 NPT Blanking Plug
- Descripción:
- Socket head pipe plug for use in blanking unused positions in intake manifold, block etc. 2 plugs 1/4-inch NPT. For help in identification, this plug measures approximately 13mm OD.
- Fabricante:
- Edelbrock
- PVP:
- —
- IVA incluído:
- —
1/8 NPT Blanking Plug
- Descripción:
- Socket head pipe plug for use in blanking unused positions in intake manifold, block etc. 2 plugs 1/8-inch NPT. For help in identification, this plug measures approximately 10mm
- Fabricante:
- Edelbrock
- PVP:
- —
- IVA incluído:
- —
3/8 NPT Blanking Plug
- Descripción:
- Socket head pipe plug for use in blanking unused positions in intake manifold, block etc. 2 plugs 3/8-inch NPT. Can be used to blank some points in some intake manifolds etc. For help in identification, this plug measures approximately 17mm OD
- Fabricante:
- Edelbrock
- PVP:
- —
- IVA incluído:
- —
Bellhousing Dowel .007 Offset
- Descripción:
- Moroso offset bellhousing dowels allow correction of bellhousing alignment with crankshaft centreline. The transmission input shaft is required to be within +/- .005" to the crank centreline to allow trouble free clutch release and reduce side load on transmission input shaft bearings. Procedure is to check bellhousing alignment, note offset required, remove stock dowels and replace in the with the Moroso part in the correct orientation. .007" Offset. Fits Small and Big Block Chevrolet V8.
- Fabricante:
- Moroso
- PVP:
- —
- IVA incluído:
- —
Bellhousing Dowel .014 Offset
- Descripción:
- Moroso offset bellhousing dowels allow correction of bellhousing alignment with crankshaft centreline. The transmission input shaft is required to be within +/- .005" to the crank centreline to allow trouble free clutch release and reduce side load on transmission input shaft bearings. Procedure is to check bellhousing alignment, note offset required, remove stock dowels and replace in the with the Moroso part in the correct orientation. .014" Offset. Fits Small and Big Block Chevrolet V8.
- Fabricante:
- Moroso
- PVP:
- —
- IVA incluído:
- —
Bellhousing Dowel .021 Offset
- Descripción:
- Moroso offset bellhousing dowels allow correction of bellhousing alignment with crankshaft centreline. The transmission input shaft is required to be within +/- .005" to the crank centreline to allow trouble free clutch release and reduce side load on transmission input shaft bearings. Procedure is to check bellhousing alignment, note offset required, remove stock dowels and replace in the with the Moroso part in the correct orientation. .021" Offset. Fits Small and Big Block Chevrolet V8.
- Fabricante:
- Moroso
- PVP:
- —
- IVA incluído:
- —
Brass Core Plugs SBC
- Descripción:
- Brass core plugs, steel cam plug and gallery plug set for use when re-building. Brass core plugs also suitable for marine use. Application: Small Block Chevrolet (most). Some engines may also require additional plugs.
- Fabricante:
- Federal Mogul
- PVP:
- —
- IVA incluído:
- —
Crank Key SBC
- Descripción:
- Mr Gasket crank key for Small Block Chevrolet. 2 required per engine.
- Fabricante:
- Mr Gasket
- PVP:
- —
- IVA incluído:
- —
Power Brake Fitting
- Descripción:
- Power brake take off. Use this convenient fitting that screws into rear port of Edelbrock Performer Series carbs to provide vacuum source for power brakes. Thread size 1/4" NPT, accepts 3/8" ID push on hose.
- Fabricante:
- —
- PVP:
- —
- IVA incluído:
- —
SBC Bellhousing Dowel
- Descripción:
- Original GM bellhousing dowel for rear of block. Damaged bellhousing dowels can result in mis-aligned bellhousing and lead to transmission damage.
- Fabricante:
- —
- PVP:
- —
- IVA incluído:
- —
SBC Dipstick Lower Tube Pre 79
- Descripción:
- Lower dipstick tube for Pre-1979 Small Block Chevrolet. This lower tube is pressed into the block to provide correct alignment for the lower section of the dipstick. Required when building from a new bare block.
- Fabricante:
- —
- PVP:
- —
- IVA incluído:
- —
SBF Cam Thrust Plate
- Descripción:
- Camshaft thrust plate used on later 302/351 engines.
- Fabricante:
- —
- PVP:
- —
- IVA incluído:
- —
SBF Plug & Dowel Kit
- Descripción:
- Complete plug and dowel kit for building or re-building most production 289, 302 and 351W blocks.
- Fabricante:
- Ford Racing
- PVP:
- —
- IVA incluído:
- —
